OPENSPRINKLER TUTORIAL HOW TO
OPENSPRINKLER TUTORIAL MANUAL
OPENSPRINKLER TUTORIAL TV

When everything is working right, bury the pipe.

Make any adjustments to the distance and directions of the sprinklers.

Now test each zone, using the timer to control the valves.

Be sure to write down which timer 'station' runs which zone and keep these notes near your timer. This guide was to simply document my progress.

Wire the valves to the timer following the instructions that come with your timer. OpenSprinkler Pi (OSPi) is an open-source sprinkler / irrigation extension board for the Raspberry Pi.

Attach the sprinklers after flushing the system with water.

Amazon US Links (Top Picks) (Best Overall) Orbit BHyve Indoor 8.

OPENSPRINKLER TUTORIAL MANUAL

Refer to the valve instructions for manual operation. In this video I tested 7 of the most popular smart automatic sprinkler systems from Rachio, Orbit BHyve, Scotts Gro, OpenSprinkler, Rainbird and Skydrop to find the BEST system for your needs.

Open each valve to flush the pipe with water, then close.

Turn on the water at the 'shut-off' to supply your system, then operate the valves manually to flush the system.

Opening the faucet to increase the water flow will increase the power and coverage of the stream, while decreasing the flow. Don't connect the sprinkler until everything is assembled so that you can flush the system with water to clear out any dirt that got in the pipes. The simplest way to change the amount of water coming out of your impact sprinkler is to tighten (clockwise) or loosen (counterclockwise) the hose faucet where it’s hooked up.

Start assembling moving from one sprinkler location to the next.

Place lengths of pipe along the string after laying out the right sprinklers and connectors at each stake.Note: Using swing joints or EZ Pipe makes positioning sprinklers easier.

It is a web-based timer and controller built upon the Arduino platform that works with standard 24VAC sprinkler valves commonly found in household watering and irrigation systems.

Poly is assembled by sliding a clamp over the pipe, insert the fitting all the way then bring the clamp into position and tighten. OpenSprinkler is the creation of Ray Wang and Chris Anderson (former editor-in-chief of Wired magazine and now the CEO of 3DRobotics).

Please let us know any questions in the comments below.Orbi. We run through all the steps and features.

OPENSPRINKLER TUTORIAL HOW TO

Read the manufacturers instructions before using PVC cement. This video shows how to use the sprinkler design tool. A primer is available to prepare the pipe and fittings for gluing.Quickly insert pipe all the way, giving a 1/4 turn to distribute the cement and hold a few seconds. PVC cement is applied to the inside of the fitting and the outside of the pipe.Rain Bird does not recommend using poly pipe for the main line connecting pipe. Poly pipe is more flexible and is less likely to be damaged by freezing. Poly pipe is mostly used in colder climates.Your system will operate better and be more durable using a larger diameter (3/4', 1', or 1 1/4'), heavier gauge (schedule 40) pipe. PVC pipe is available in a variety of diameters and wall thickness'.Connect the back-flow preventer if required. Did you check with your Rain Bird Dealer to find out which connections are right for your local codes and conditions? Be sure to put enough space between valves on the manifold so that they can be removed in case they ever need to be replaced. To make trenching easier ask your local tool rental supplier about a 'power trencher.' If you are using a Poly Pipe, ask about a pipe pulling machine, which will bury pipe without digging up your lawn.It may take a while, and it will get muddy so turn off the water once in a while to let the water soak in. Now turn on the water and work your way through. Dig your trench up to the walk on both sides.On the other end glue a slip-male thread adapter and connect a Jet Spray Nozzle (available at most home improvement and home & garden retailers). Get a piece of PVC long enough to go under the walk, glue a slip-female thread adapter to one end and attach a hose. To run pipe under existing walkways you can 'drill' using water pressure.Typical trench depths range from 6 to 12 inches.

Mark the sprinkler locations with flags or the stakes. Be sure to call your utility companies if you need help.

OPENSPRINKLER TUTORIAL TV

STOP! Make sure you know where all gas lines, power lines and cable TV lines are before you start to dig. Use string to show where the pipe will run.

Place a stake or flag at every sprinkler location as indicated on your layout.

Val reply = 'Bewässerung für *' + station_label + '* wurde gestartet. Laufzeit *' + station_rwt + '*. Ausgelöst von *' + + '*.'

Val station_rwt = (station_name + 'RemainingWaterTime').state.toString OpenSprinklerAllStationsOff.postUpdate(NULL) ndTelegramAnswer(Long::parseLong(),, reply) Opensprinkler.things Bridge opensprinkler:http:http 'OpenSprinkler HTTP Interface' 'OSPI' ]

Opensprinkler tutorial